BBMC

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is a nuisance. This can be an opportunity to upgrade to energy-efficient windows replacements near me or insulated ones, and reap benefits such as improved comfort, increased resale values and reduced utility bills.

You can do it yourself for only a fraction of the cost it would cost to employ an expert. It requires the right equipment and an hour or two of your time.

Glass

Replace your single-paned windows with tempered insulate glass to improve the efficiency of your energy, reduce noise, and protect the historic integrity of your older home. The process of replacing a window pane is relatively simple and can be done by anyone with basic hand tools. In addition to a new pane, the following tools are needed: latex glazing putty; Glazier's points; pliers and the use of a heat gun to warm the old putty, if necessary. Before beginning, wear gloves and safety goggles as working with broken glass could cause injuries.

Take out any broken glass pieces remaining. This is best accomplished with the help of pliers however, a flathead screwdriver may be effective in a pinch. Use a wood chisel, or putty knife to get rid of any old putty remaining around the frame and the window sash. Be careful to not break the window sash. Be careful and slow. It is recommended to work on a sturdy ladder instead of the ground and have someone standing below the sash to help keep it steady.

Prepare the window frame to accommodate the new pane when you have removed the old glue. To allow for seasonal expansion or contraction by subtracting 1/8 inch from the measurements of the width and height. These measurements can be taken to a home center or hardware store to get a piece cut of glass that is in stock to the correct size. Alternatively, you can cut the glass yourself if have the appropriate tools.

After putting in the new pane After installing the new pane, apply a small amount of caulking around the edge to ensure it is weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to hold the pane in its place. The points shouldn't be so tight as to cause friction between the sash and frame, but they also shouldn't be too loose.

Before putting the putty on, knead it thoroughly until it is soft and free of lumps. Then, roll it into pencil-size strips. The first strip should be glued to the frame's corner. Work from one corner to the next and ensure that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of steel that allow glass windows replacement near me to be secured to the frame without causing damage to the delicate surface. It's easy to learn how to use this nefarious tool, and you'll be able to save money on the expense of an expert installation.

Once the old putty and the glazier's points have been removed, thoroughly clean the frame with a utility knife to get rid of any remaining traces. Lightly sand the frame in the rabbet grooves to smooth out rough areas. If you sand wood, protect it with painter’s tape to avoid accidental damage.

Note down the dimensions of the frame. Bring these measurements to an hardware store or home center and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new window in the frame and press it in place by using your hands. Make use of the point of the chisel, or the edge of the putty blade to smudge the glaziers' points as illustrated in Figure 11. The glazier's point should be in line with the top edge of your pane and the shoulders raised should be just below that lip.

Apply a thin bead of glazing compound on the edges of the new glass and in the rabbet grooves to seal and protect them. Allow it to dry and cure completely.

Install the new window sash after the glazing compound has dried. First, coat the wood with a heavy coat of Linseed oil. This will prevent the newly-created putty from drying out or cracking due to the moisture it absorbs. Apply this coat with a brush or the tip of your knife, and then employ the chisel or back end from the putty knife to gently press the new sash and glazier's point into the grooves of the rabbet. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A hurled baseball or a rock that is errant or a falling branch can cause a window pane to crack or break. Fortunately, the majority of replacement windows panes can be replaced by simply placing a new piece of glass in its the right place. The glass is held into place by a small metal clip, also known as a glazier’s point and putty. This compound is also referred to as glazing compound. Before you install a new pane, first take out the old one and clean the area using the help of a rag, the pull-type paint scraper or the wood chisel. Wear protective glasses and gloves while you do this work. If the window is attached to the frame, you'll need make use of a heat gun to soften the adhesive before prying it free.

If you are planning to reinstall your original sash, remove the mold that holds the old pane. Then, sand the sash to make sure it's flat and ready for a new caulk. Once the sash is installed and sanded, apply a fresh silicone caulk around the glass to ensure that it doesn't swell or fade as time passes.

Take the glazing points out of the rabbets and the grooves in the sash that the glass sits. If they're hard to chisel, hold the hand tool, such as a heating gun over them to allow them to soften before. If you're using a heated gun, make sure not to damage the railings of the sash or the sash itself by using the tool too close.

Make a bed for your new pane by removing the old glaze and putty. Roll a piece of glazing compound between your hands, shaping it to be around 1/2-inch thick. Then, you can press it into the rabbets in which the glass will sit. The glass should rest against the putty on both sides. If necessary, lightly tap your glass into the rabbet with your thumb.

If the new pane has a crack, you can cover it with a solvent-based glass glue or silicone caulk prior pressing it into the sash. If the crack isn't sealed, you'll need to use putty to keep the water out. Once the putty is dry remove the oily film off the glass and let it dry completely before you paint. Paint after the putty has completely dried. It will not form a good seal and may discolor or leak over time.

Paint

If you've experienced a broken window pane, then you may be worried about the expense of replacing it. However, replacing a single glass pane doesn't require a huge amount of money when you do it yourself. In fact, even a double glazing replacement window-pane window can be replaced for a fraction of the cost of an expert.

First, if you are working on a large-sized window, make sure it is securely fixed to the frame. This is relatively easy and quick with the proper tools and techniques.

When you are ready to start with the removal of the window pane. Pry out the metal glazing points that are attached to it. These are essentially small metal triangles that act as "nails" which hold the window in in the wood frame. They are placed under a bead or glazing glue that hardens to solid wedge which holds the wood frame in place and hides the points.

After you have the old pane taken away clean the surrounding frame and wood. Scrape off any old paint, and sand the rabbet grooves in which the glazing points were. Sand them down to clean wooden surfaces, allowing you to paint the frames the same shade. After sanding, apply a coat of flax oil to the wood's surface to help extend its lifespan.

Next, measure the size of the window's opening. It is necessary to take vertical and horizontal measurements of the entire opening as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. Take these dimensions to the hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new replacement Window Near Me pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.